DAELIM S2 125 страница 142 Скачать руководство пользователя

Страница: 142 / 184

12-19

FRONT WHEEL/FRONT FORK/STEERING/BRAKE

●

Remove the steering stem nut using the steering stem
nut socket.

TOOL : STEERING STEM NUT SOCKET

●

Remove the steering top thread nut using the steering
stem socket.

TOOL : STEERING STEM SOCKET

●

Remove the top cone race.

●

Check the upper ball assembly, top cone race and ball
race for damage or abnormal and replace as necessary.

●

Check the bottom cone race for wear and damage.

STEERING STEM

REMOVAL

●

Remove the following parts.

Handle cover

Handle bar

Front cover

Front under cover

Inner cover

Front wheel

Front fork

●

Install the front fork to the steering stem.

●

Install the front fork setting bolts.

TORQUE VALUE : 7.5 kgf

●

Install the brake hose clip A to the RH. front fork.

Be careful not to turn over the vehicle.

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды