DAELIM S2 125 Скачать руководство пользователя страница 25

Страница: 25 / 184

2-4

INSPECTIONS / ADJUSTMENTS

FUEL LINE(FUEL TUBE)

●

Remove the luggage box

●

Check the fuel tube of the fuel auto cock connected to
the fuel tank and carburetor. If the fuel tube is cranked,
damaged or leaks, replace it.

THROTTLE GRIP OPERATION

●

Check if the throttle grip operates smoothly in any
steering position.

●

If the throttle grip does not operate properly, lubricate
the throttle cable.

●

If the throttle grip does not operate properly, check the
throttle cable for aging, damage or kinking.

●

Check the throttle grip free play.

FREE PLAY : 2~6mm

●

For main adjustment, loosen the lock nut and turn
adjuster.

●

After adjusting, tighten lock nut. After adjustment is
completed, recheck the throttle grip free play.

●

For simple adjustment, use the adjuster under the
throttle grip. RH.

●

Remove the Rubber.

●

Loosen the lock nut and turn the adjuster.

LOCK NUTS

ADJUSTRING NUTS

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды