manualshive.com logo in svg

DAELIM S2 125, Руководство по обслуживанию

Поделиться
Скачать
DAELIM S2 125 Скачать руководство пользователя страница 116

11-5

TRANSMISSION/CRANKSHAFT/CRANKCASE

TRANSMISSION ASSEMBLY

●

Install the drive shaft on the transmission cover.

●

Install a new drive shaft oil seal.

TOOLS : CRANK ASSEMBLY SHAFT

CRANK ASSEMBLY COLLAR

TRANSMISSION BEARING INSPECTION

●

Check that the bearing outer race fits the case tightly
without play.

●

Turn the inner race and check that the bearing turns
smoothly and quietly.

●

Replace the bearings if necessary.

●

Install the bearing to the case with special tools.

TOOLS : DRIVE HANDLE A

OUTER DRIVER
DRIVER PILOT

●

Check the LH. crankcase oil seal for wear or damage.

●

Inatall the final shaft and counter shaft on the LH.
crank case.

BEARING

OUTER

DRIVER

OUTER
HANDLE

DRIVER

PILOT

CRANK ASSEMBLY COLLAR

CRANK ASSEMBLY SHAFT

FINAL SHAFT

COUNTER SHAFT

Содержание S2 125

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды