DAELIM S2 125 Скачать руководство пользователя страница 46

Страница: 46 / 184

4-7

LUBRICATION SYSTEM

RADIATOR

REMOVAL

●

Remove the front cover.

(

⇨

3-5)

●

Remove the front wheel.

(

⇨

12-4)

●

Loosen the 2 oil bolts and the 4 drain cock packings
from the main pipe bracket.

●

Loosen the 3 flange bolts securing the radiator.

●

Remove the radiator.

INSPECTION

●

Check the oil line connections for leaks.

●

Check the oil cooler for bent or collapsed fins.
Straighten the bent or collapsed fins with a suitable,
small, blade-type screw driver if necessary.

●

Check the air passages for clogging or restriction. Blow
dirt out from between core fins with compressed air or
wash off dirt with water.

●

After installing, start the engine and check for leak. Stop
the engine and check the oil level.

FIN

OIL RADIATOR

RADIATOR RUBBER

RADIATOR COLLAR

FLANGE BOLT

•

Be careful not to damage the radiator when removing it.

•

Pay attention not to turn over the vehicle.

FLANGE BOLTS

RADIATOR

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды