DAELIM S2 125 Скачать руководство пользователя

Страница: 137 / 184

●

Apply the silicone grease to the boot.

●

Connect the boot to the portion of the caliper.

●

Install the pad spring in the caliper.

●

Install the caliper pin bolt and the slide pin in the
caliper.

●

Install the brake pad and the hanger pin in the caliper.

●

Install the front caliper to the front fork

●

Tighten the bolt to the specified torque.

TORQUE VALUE : 3.0kgf

●

Connect the brake hose to the caliper and install 2
sealing washers and oil bolt.

●

Tighten the oil bolt to the specified torque

TORQUE VALUE : 3.4kgf

●

Fill the brake fluid to the upper limit line and bleed air.

FRONT FORK

REMOVAL

●

Remove the following parts.

Front under cover

Front brake caliper

Front fender

Front wheel

●

When removing the front fork, loosen the fork pipe
bolt lightly.

●

Loosen the 4 setting bolts securing the RH./LH. front
fork, remove the RH./LH. front fork.

●

After removal of RH. front fork, loosen the flange bolt
and remove the front brake hose clamp A.

12-14

FRONT WHEEL/FRONT FORK/STEERING/BRAKE

Support the vehicle securely under the engine not to
turn over it.

Loosen the fork pipe bolt, but do not remove it.

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды