manualshive.com logo in svg

DAELIM S2 125, Руководство по обслуживанию

Поделиться
Скачать
DAELIM S2 125 Скачать руководство пользователя страница 119

11-8

TRANSMISSION/CRANKSHAFT/CRANKCASE

MEASURING

POINT

DIAL
GAUGE

FEELER GAUGE

DIAL GAUGE

BEARINGS

OIL SEAL

CRANKSHAFT INSPECTION

●

Place the crankshaft on a stand or V-block, and measure
the crankshaft runout using dial gauge.

SERVICE LIMIT : RIGHT : 0.1 mm

LEFT : 0.1 mm

TRANSMISSION BEARING

●

Remove the transmission and crankshaft.

INSPECTION

●

Check that the bearing outer race fits the case tightly
without play.

●

Turn the inner race and check that the bearing turns
smoothly and quietly.

●

Replace the bearing if necessary.

●

Measure the connecting rod radial clearance in both X
and Y directions.

●

Replace the crankshaft if the service limit is exceeded.

SERVICE LIMIT : 0.05 mm

●

Measure the side clearance by inserting the feeler
gauge between the crankshaft and connecting rod big
end as shown.

TOOL : FEELER GAUGE

Содержание S2 125

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды