DAELIM S2 125 Скачать руководство пользователя

Страница: 127 / 184

12-4

FRONT WHEEL/FRONT FORK/STEERING/BRAKE

●

Lubricate the throttle grip front end with grease and
then install the throttle grip.

●

Connect the throttle cable to the throttle grip.

●

Install the right and left handlebar switches and tighten
the screws.

●

Install the front and rear brake master cylinders.

●

Install in the reverse order of removal.

FRONT WHEEL

REMOVAL

●

Jack the motorcycle front wheel off the ground.

●

Remove the front axle nut to pull out the axle.

●

Remove the front wheel and the speedometer gear unit.

INSPECTION

AXLE RUNOUT

●

Set the axle in V blocks and measure the runout using a
dial gauge.

●

The actual runout is 1/2 of the total indicator reading.

SERVICE LIMIT : 0.2mm replace if over

Adjust the throttle grip free play to the specified
range of 2~6mm.

Install the brake master cylinders by aligning the
index marks.

DIAL GAUGE

AXLE

BRAKE MASTER CYLINDER

AXLE NUT

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды