DAELIM S2 125 Скачать руководство пользователя страница 52

Страница: 52 / 184

5-3

FUEL SYSTEM

FUEL TANK

REMOVAL

●

Release the seat lock by turning the main switch key to
open the seat.

●

Remove the following parts.

Luggage box

. (

⇨

3-2)

Floor panel leg

Center cover.

Rear center cover.

Rear carrier/Back rest

Body cover.

●

Remove the fuel tube from the fuel tank.

●

Remove the tube between the fuel tank and the fuel
filter.

●

Remove the fuel vapor tub.

●

Remove the fuel tank.

●

Install in the revers order of removal

CARBURETOR

REMOVAL

●

Remove the luggage box.

(

⇨

3-2)

●

Remove the center cover.

(

⇨

3-3)

●

Remove the air cleaner.

(

⇨

2-5)

●

Loosen the throttle cable lock nut, and remove the
throttle cable from the carburetor.

●

Remove the fuel tube from the carburetor.

•

After removing the fuel tank, be sure to close the
fuel tank cap.

•

Gasoline is extremely flammable. Avoid fire during
work, and pay particular attention to electric sparks.
Furthemore, the evaporated (gasified) gasoline is
highly explosive. Work in a well-ventilated areas.

FUEL TANK

AUTO BYSTARTER

●

Remove the wiring coupler of the auto bystarter.

●

Loosen the set plate setting screw.

●

Loosen the screw of the carburetor insulator band 46.

●

Remove the carburetor.

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды