DAELIM S2 125 Скачать руководство пользователя страница 42

Страница: 42 / 184

4-3

LUBRICATION SYSTEM

UPPER LINE

PROPER LINE
LOWER LINE

SIGHT GLASS

OIL DRAIN PLUG

OIL PICK
UP COLLAR

OIL FILTER
SCREEN

TAPPET ADJUSTING
HOLE CAP

ENGINE OIL LEVEL INSPECTION

●

Erect the motorcycle on the main stand.

●

Warm up the engine to heat the engine oil to an
appropriate level.

●

Stop the engine, and check the oil level line on the
sight-glass installed on the LH. crank case cover.

●

If the oil level is between the lower and higher sight-
glass oil level line, oil level is satisfactory. If the oil
level is below or near the lower level mark, add the
recommended engine oil.

ENGINE OIL CHANGE

●

Loosen the oil drain plug bolt and drain engine oil.

●

Operate the kick starter arm several times to remove
the remaining oil from the engine.

●

Tighten the oil drain plug bolt.

TORQUE VALUE : 2.0-3.0 kgf

TORQUE VALUE : 1.5 kgf

●

Loosen the special screw, remove the plug maintenance
cover.

●

Fill the recommended oil after opening oil filter cap of
cylinder head cover.

OIL CAPACITY : 1.1

ℓ

(After disassembly)

0.9

ℓ

(After Oil change with Oil in
the Oil hose removed)

0.8

ℓ

(After Oil filter change)

0.75

ℓ

(After Oil change)

●

API service classification : SE, SF, SH grade.

●

Start the engine and keep it idle for a few minutes.

●

Stop the engine and check the oil level. If the oil level
is low, add the recommended engine oil.

●

Check on oil leaks.

•

To completely and rapidly drain engine oil, warm up
engine and erect the motorcycle on its side stand.

•

It is extremely important to replace oil filter or clean
the oil filter screen at the first maintenance interval
(after 1,000Km).

•

Clean the oil filter screen every 4,000Km.

•

Clean the filter screen with fresh cleaning oil.

•

Check the hole cap O-ring for satisfactory condition.

•

Tighten the hole cap with specified tightening
torque.

OIL FILTER CAP

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Бренды по названию

Популярные бренды