D-Link DES-3326SRM Скачать руководство пользователя | Manualshive

Страница: 201 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

IP Interface Commands

201

config ipif System

Purpose

Used to configure the System IP interface.

Syntax

config ipif System [{vlan
<vlan_name>/ipaddress
<network_address>/state
[enabled/disabled]/bootp/dhcp}]

Description

This command is used to configure the
System IP interface on the switch.

Parameters

<vlan_name>

−

The name of the VLAN

corresponding to the System IP interface.

<network_address>

−

IP address and

netmask  of  the  IP  interface  to  be  created.
You  can  specify  the  address  and  mask
information using the  traditional format (for
example,  10.1.2.3/255.0.0.0  or  in  CIDR
format, 10.1.2.3/16).

state [enabled/disabled]

−

Allows you to

enable or disable the IP interface.

bootp

−

Allows the selection of the BOOTP

protocol for the assignment of an IP address
to the switch

’

s System IP interface.

dhcp

−

Allows the selection of the DHCP

protocol for the assignment of an IP address
to the switch

’

s System IP interface.

Restrictions

Only administrator-level users can issue
this command.

«
...
199
200
201
202
203
...
»

Содержание DES-3326SRM



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326SRM

Бренд: Grozone Control Страницы: 20

Бренд: Comtrend Corporation Страницы: 2

VH M 1 1 1 Series

Бренд: Jlso Tec Trade Страницы: 15

CRSMEO-4 Series

Бренд: Festo Страницы: 16

Бренд: Fairchild Страницы: 20

Бренд: Steren Страницы: 13

Бренд: Inline Страницы: 4

Бренд: Allen-Bradley Страницы: 4

Бренд: 3One data Страницы: 9

Бренд: Black Box Страницы: 15

ePowerSwitch 8XM Master

Бренд: ADDER Страницы: 2

Бренд: Lutron Electronics Страницы: 2

JetNet 5428G-20SFP Series

Бренд: Korenix Страницы: 2

TU2-700 - DATA SHEETS

Бренд: TRENDnet Страницы: 9

Бренд: Imagine Страницы: 93

Бренд: J-Tech Digital Страницы: 13

Бренд: Blaze Страницы: 18

Бренд: Johansson Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды