D-Link DES-3326SRM Скачать руководство пользователя

Страница: 116 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

116

Network Monitoring Commands

create syslog host

local4

−

Specifies that local use 4 messages

will be sent to the remote host. This
corresponds to number 20 from the list
above.

local5

−

Specifies that local use 5 messages

will be sent to the remote host. This
corresponds to number 21 from the list
above.

local6

−

Specifies that local use 6 messages

will be sent to the remote host. This
corresponds to number 22 from the list
above.

local7

−

Specifies that local use 7 messages

will be sent to the remote host. This
corresponds to number 23 from the list
above.

udp_port <int>

−

Specifies the UDP port

number that the syslog protocol will use to
send messages to the remote host.

ipaddress <ipaddr>

−

Specifies the IP address of

the remote host where syslog messages will be
sent.

state [enabled/disabled]

−

Allows the sending of

syslog messages to the remote host, specified
above, to be enabled and disabled.

Restrictions

Only administrator-level users can issue this
command.

Example Usage:

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды