D-Link DES-3326SRM Скачать руководство пользователя страница 121

Страница: 121 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Network Monitoring Commands

121

config syslog host

number that the syslog protocol will use to send
messages to the remote host.

ipaddress <ipaddr>

−

Specifies the IP address of

the remote host where syslog messages will be
sent.

state [enabled/disabled]

−

Allows the sending of

syslog messages to the remote host, specified
above, to be enabled and disabled.

Restrictions

Only administrator-level users can issue this
command.

Example Usage:

To configure a syslog host:

DES-3326SR:4#config syslog host all severity all facility local0

Command: config syslog host all severity all facility local0

Success.

DES-3326SR:4#

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды