D-Link DES-3326SRM Скачать руководство пользователя | Manualshive

Страница: 190 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

190

Link Aggregation Commands

config link_aggregation

Purpose

Used to configure a previously created link
aggregation group.

Syntax

config link_aggregation group_id <value>
{master_port <port>/ports <portlist>/
{state [enabled/disabled]}

Description

This command allows you to configure a link
aggregation group that was created with the
create link_aggregation command above.

Parameters

<value>

−

Specifies the group id. The switch

allows up to 6 link aggregation groups to be
configured. The group number identifies
each of the groups.

<port>

−

Master port ID. Specifies which

port (by port number) of the link aggregation
group will be the master port. All of the
ports in a link aggregation group will share
the port configuration with the master port.

<portlist>

−

specifies a range of ports to be

configured.    Ports  are  specified  by  entering
the lowest port number in a group, and then
the  highest  port  number  in  a  group,
separated  by  a  dash.    So,  a  port  group
including the switch ports 1, 2, and 3 would
be  entered  as  1-3.    Ports  that  are  not
contained  within  a  group  are  specified  by
entering  their  port  number,  separated  by  a
comma.  So, the port group 1-3 and port 26
would  be  entered  as  1-3,  26.    Additional
ports  can  be  individually  entered  by  their

«
...
188
189
190
191
192
...
»

Содержание DES-3326SRM



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326SRM

Бренд: Daxten Страницы: 7

Бренд: H3C Страницы: 90

Бренд: StarTech.com Страницы: 2

Бренд: AVLT-Power Страницы: 12

Бренд: Ribimex Страницы: 15

Unified Gigabit Wireless PoE Switch 24...

Бренд: 3Com Страницы: 40

Бренд: Vega Страницы: 44

Бренд: UNICOM Страницы: 15

Бренд: Allen-Bradley Страницы: 2

MaxiiNet VI3026

Бренд: Vigitron Страницы: 288

kontron KSwitch D3 UM

Бренд: S&T Страницы: 38

PICO-GUARD SFI-D1EDPXT6

Бренд: Banner Страницы: 2

Бренд: Labgear Страницы: 8

Бренд: EtherWAN Страницы: 239

Бренд: Minicom Страницы: 16

Бренд: Pilz Страницы: 20

Бренд: Gembird Страницы: 11

Бренд: A-Neuvideo Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды