manualshive.com logo in svg

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Поделиться
Скачать
D-Link DES-3326SRM Скачать руководство пользователя страница 282

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

282

 

DVMRP Commands 

 

config dvmrp 

Purpose 

Used to configure DVMRP on the switch. 

Syntax 

config dvmrp [ipif <ipif_name>/all] 
{metric <value>/probe 
<second>/neighbor_timeout 
<second>/state [enabled/disabled] 

Description 

This  command  is  used  to  configure  DVMRP 
on the switch. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

for which DVMRP is to be configured. 
all 

−

  Specifies  that  DVMRP  is  to  be 

configured for all IP interfaces on the switch. 
metric <value> 

−

 Allows the assignment of a 

DVMRP route cost to the above IP interface.  
A  DVMRP  route  cost  is  a  relative  number 
that  represents  the  real  cost  of  using  this 
route  in  the  construction  of  a  multicast 
delivery tree.  It is similar to, but not defined 
as, the hope count in RIP.  The default is 1. 
probe  <second> 

−

  DVMRP  defined  an 

extension  to  IGMP  that  allows  routers  to 
query  other  routers  to  determine  if  a 
multicast group is present on a given router 
subnetwork  or  not.    This  is  referred  to  as  a 

‘

probe

’

.  The default value is 10 seconds. 

neighbor_timeout  <second> 

−

  The  time 

period  for  which  DVMRP  will  hold  Neighbor 
Router  reports  before  issuing  poison  route 
messages.  The default value is 35 seconds. 
state  [enabled/disabled] 

−

  Allows  DVMRP  to 

be enabled or disabled. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

Содержание DES-3326SRM



































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды