D-Link DES-3326SRM Скачать руководство пользователя

Страница: 87 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Network Management Commands

ping

Purpose

Used to test the connectivity between
network devices.

Syntax

ping <ipaddr> {times <value>} {timeout
<sec>}

Description

This  command  sends  Internet  Control
Message Protocol (ICMP) echo messages to
a  remote  IP  address.    The  remote  IP
address  will  then

“

echo

”

or return the

message. This is used to confirm
connectivity between the switch and the
remote device.

Parameters

−

the IP address of the remote

device.

times <value>

−

the number of individual

ICMP echo messages to be sent.  A value of
0  will  send  an  infinite  ICMP  echo
messages.    The  maximum  value  is  255.
The default is 0

timeout <sec>

−

defines the time-out

period  while  waiting  for  a  response  from
the  remote  device.    A  value  of  1  to  99
seconds can be specified.  The default is 1
second.

Restrictions

Only administrator-level users can issue
this command.

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды