D-Link DES-3326SRM Скачать руководство пользователя страница 327 | Manualshive

Страница: 327 / 354

D-Link DES-3326SRM Скачать руководство пользователя страница 327

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

OSPF Configuration Commands

327

show ospf virtual neighbor

Purpose

Used to display the current OSPF virtual
neighbor router table.

Syntax

show ospf virtual_neighbor {<area_id>}

Description

This command will display the current OSPF
virtual neighbor router table.

Parameters

<area_id>

−

A 32-bit number in the form of

an

IP

address

(xxx.xxx.xxx.xxx) that

uniquely identifies the OSPF area in the
OSPF domain.

<neighbor_id>

−

The OSPF router ID for the

remote area.  This is a 32-bit number in the
form  of  an  IP  address  (xxx.xxx.xxx.xxx)  that
uniquely  identifies  the  remote  area

’

s Area

Border Router.

Restrictions

none.

Usage Example

To display the current OSPF virtual neighbor table:

DES-3326SR:4#show ospf virtual_neighbor
Command: show ospf virtual_neighbor

Transit Router ID of IP Address of Virtual Neighbor
Area ID Virtual Neighbor Virtual Neighbor  State
--------------- ----------------     ----------------    ----------------
10.1.1.1    10.2.3.4     10.48.74.111    Exchange

DES-3326SR:4#

«
...
325
326
327
328
329
...
»

Содержание DES-3326SRM



































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды