D-Link DES-3326SRM Скачать руководство пользователя страница 265

Страница: 265 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

DNS Relay Commands

265

To delete an entry domain name dns1, IPaddress 10.43.21.12
from DNS static table.

DES-3326SR:4#config dnsr delete static dns1 10.43.21.12
Command: config dnsr delete static dns1 10.43.21.12

Success.

DES-3326SR:4#

enable dnsr

Purpose

Used to enable DNS relay.

Syntax

enable dnsr

Description

This command is used, in combination with
the disable dnsr command below, to enable
and disable DNS Relay on the switch.

Parameters

none.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To enable status of DNS relay:

DES-3326SR:4#enable dnsr
Command: enable dnsr

Success.

DES-3326SR:4#

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды