D-Link DES-3326SRM Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 354

D-Link DES-3326SRM Скачать руководство пользователя страница 153

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

QOS Commands

153

config bandwidth_control

<value 1-1000>

−

Specifies the limit, in

Mbps, that the above ports will be
allowed to receive packets.

tx_rate

−

Specifies that one of the

parameters below (no_limit or <value 1-
1000>) will be applied to the rate at which
the above specified ports will be allowed to
transmit packets.

no_limit

−

Specifies that there will be no

limit on the rate of packets received by
the above specified ports.

<value 1-1000>

−

Specifies the limit, in

Mbps, that the above ports will be
allowed to receive packets. Gigabit ports
must be configured to using a limit value
that is a multiplt of 8 i.e. for Gigabit
ports <value 8-1000 in increments of 8>.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To configure bandwidth control:

DES-3326SR:4#config bandwidth_control 1-10 tx_rate 10
Command: config bandwidth_control 1-10 tx_rate 10

Success.

DES-3326SR:4#

«
...
151
152
153
154
155
...
»

Содержание DES-3326SRM



































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды