D-Link DES-3326SRM Скачать руководство пользователя

Страница: 321 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

OSPF Configuration Commands

321

Command: delete ospf aggregation 10.1.1.1 10.48.76..122/16
Lsdb_type summary

Success.

DES-3326SR:4#

config ospf aggregation

Purpose

Used to configure the OSPF area aggregation
settings.

Syntax

config ospf aggregation <area_id>
<network_address> lsdb_type [summary]
advertise [enabled/disabled]

Description

This command is used to configure the
OSPF area aggregation settings.

Parameters

<area_id>

−

A 32-bit number in the form of

address

(xxx.xxx.xxx.xxx) that

uniquely identifies the OSPF area in the
OSPF domain.

<network_address>

−

The 32-bit number in

the form of an IP address that uniquely
identifies the network that corresponds to
the OSPF Area.

lsdb_type [summary]

−

Specifies the type of

address aggregation.

advertise [enabled/disabled]

−

Allows for the

advertisement trigger to be enabled or
disabled.

Restrictions

Only administrator-level users can issue
this command.

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды