D-Link DES-3326SRM Скачать руководство пользователя страница 256

Страница: 256 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

256

Bootp Relay Commands

config bootp_relay

Purpose

Used to configure the BOOTP relay feature of
the switch.

Syntax

config bootp_relay {hops <value>} {time
<sec>}

Description

This command is used to configure the
BOOTP relay feature.

Parameters

hops <value>

−

Specifies the maximum

number of router hops that the BOOTP
packets can cross.

time <sec>

−

The minimum time in seconds

within which the switch must relay the
BOOTP request. If this time is exceeded, the
switch will drop the BOOTP packet.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To configure bootp relay status.

DES-3326SR:4#config bootp_relay hops 4 time 2
Command: config bootp_relay hops 4 time 2

Success.

DES-3326SR:4#

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды