D-Link DES-3326SRM Скачать руководство пользователя страница 211

Страница: 211 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Arp Commands

211

config arp_aging

Purpose

Used to configure the age-out timer for ARP
table entries on the switch.

Syntax

config arp_aging time <value>

Description

This  command  sets  the  maximum  amount
of  time,  in  seconds,  that  an  ARP  entry  can
remain  in  the  switch

’

s ARP table, without

being accessed, before it is dropped from the
table.

Parameters

time <value>

−

The ARP age-out time, in

seconds. The default is 20.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To configure ARP aging time:

DES-3326SR:4#config arp_aging time 30
Command: config arp_aging time 30

Success.

DES-3326SR:4#

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Бренды по названию

Популярные бренды