D-Link DES-3326SRM Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 354

D-Link DES-3326SRM Скачать руководство пользователя страница 52

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

52

Switch Port Commands

5 Enabled   Auto Link Down Enabl ed
6 Enabled   Auto Link Down Enabled
7 Enabled   Auto Link Down Enabled

show port_security

Purpose

Used to display the current portr lock
configuration.

Syntax

show port_security {<portlist>}

Description

This command is used to display the
current port lock configuration of a range of
ports.

Parameters

<portlist>

−

specifies a range of ports to be

viewed.    The  port  list  is  specified  by  listing
the lowest switch number and the beginning
port number on that switch, separated by a
colon.    Then  highest  switch  number,  and
the  highest  port  number  of  the  range  (also
separeted  by  a  colon)  are  specified.    The
beginning and end of the port list range are
seperated  by  a  dash.    For  example,  1:3
would specify switch number 1, port 3.  2:4
specifies  switch  number  2,  port  4.    1:3-2:4
specifies  all  of  the  ports  between  switch  1,
port  3  and  switch  2,  port  4

−

in numerical

order.

Restrictions

none.

«
...
50
51
52
53
54
...
»

Содержание DES-3326SRM



































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды