D-Link DES-3326SRM Скачать руководство пользователя

Страница: 258 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

258

Bootp Relay Commands

config bootp_relay delete

Purpose

Used to delete one or all IP destination
addresses from the switch

’

s BOOTP relay

table.

Syntax

config bootp_relay delete ipif <ipif_name>
<ipaddr>

Description

This command is used to delete one or all of
the IP destination addresses in the switch

’

BOOTP relay table.

Parameters

<ipif_name>

−

The name of the IP interface

that contains the IP address below.

−

The BOOTP server IP address.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To delete a BOOTP relay.

DES-3326SR:4#config bootp_relay delete ipif System 10.43.21.12
Command: config bootp_relay delete ipif System 10.43.21.12

Success.

DES-3326SR:4#

Содержание DES-3326SRM



































































































































































































































































































































































Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды

D-Link DES-3326SRM, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326SRM

Отзывы:

Похожие инструкции для DES-3326SRM

Бренды по названию

Популярные бренды