Comtrol RocketLinx ES7528 Скачать руководство пользователя страница 30

Страница: 30 / 144

30 - RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

Admin Password

You can change the user name and the password here to enhance security.

IP Configuration

This function allows you to configure the switch’s IP address settings.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want to maintain these settings if the

RocketLinx ES7528 is powered off.

Admin Password

Description

User name

You can enter a new user name here. The default setting

admin

Password

You can enter a new password here. The default setting

admin

Confirm Password You need to type the new password again to confirm it.
Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you

want to maintain these settings if the
RocketLinx ES7528 is powered off.

IP Configuration

Description

DHCP Client

You can select to

Enable

Disable

the DHCP Client function.

When the DHCP Client function is enabled, an IP address is

assigned to the switch from the network’s DHCP server. In this

mode, the default IP address is replaced by the one assigned by

DHCP server. If DHCP Client is disabled, then the IP address

that you specified is used.

IP Address

You can assign the IP address reserved by your network for the

RocketLinx ES7528. If the DHCP Client function is enabled,

you do not need to assign an IP address to the RocketLinx

ES7528, because it is overwritten by the DHCP server and dis-

plays here. The default IP is 192.168.250.250.

Subnet Mask

You can assign the subnet mask for the IP address here. If the

DHCP Client function is enabled, you do not need to assign the

subnet mask. The default Subnet Mask is 255.255.255.0.

Note: In the CLI, the enabled bit of the subnet mask is used to

represent the number displayed in the web management
interface. For example, 8 represents: 255.0.0.0,16
represents: 255.255.0.0, 24 represents: 255.255.255.0.

Default Gateway

You can assign the gateway for the switch here. The default

gateway is 192.168.250.1.

Note: In the CLI, use 0.0.0.0/0 to represent the default

gateway.

Switch Setting

Description

Содержание RocketLinx ES7528

















































































































































Результаты поиска

Содержание RocketLinx ES7528

Отзывы:

Похожие инструкции для RocketLinx ES7528

Бренды по названию

Популярные бренды

Comtrol RocketLinx ES7528, Руководство пользователя

Результаты поиска

Содержание RocketLinx ES7528

Отзывы:

Похожие инструкции для RocketLinx ES7528

Бренды по названию

Популярные бренды