Comtrol RocketLinx ES7528 Скачать руководство пользователя страница 34

Страница: 34 / 144

34 - RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

Jumbo Frame

The typical Ethernet frame range is from 64 to 1,518 bytes. This is

sufficient for general usages. However, when users want to transmit

large files, the files may be divided into many small size packets.

When the transmission speed becomes slow, long size Jumbo frame

may solve the issue.
The RocketLinx ES7528 allows you configure the size of the

Maximum Transmission Unit (MTU). The default value is 1,518

bytes. You can increase the MTU size to support jumbo frames on

all interfaces by setting the Jumbo Frame MTU. The maximum

Jumbo Frame size is 9,216 bytes. You can freely change the

available packet size.

Jumbo Frame

Description

System MTU

Change the MTU size for all Fast Ethernet interfaces on the switch stack. The

range is 1500 to 1546 bytes; the default is 1518 bytes.

Jumbo Frame MTU

Change the MTU size for all gigabit Ethernet interfaces on the switch stack.

The range is 1500 to 9216 bytes; the default is 1518 bytes.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want to maintain these

settings if the RocketLinx ES7528 is powered off.

Reset

Click to reset the MTU to the default value.

Содержание RocketLinx ES7528

















































































































































Результаты поиска

Содержание RocketLinx ES7528

Отзывы:

Похожие инструкции для RocketLinx ES7528

Бренды по названию

Популярные бренды

Comtrol RocketLinx ES7528, Руководство пользователя

Результаты поиска

Содержание RocketLinx ES7528

Отзывы:

Похожие инструкции для RocketLinx ES7528

Бренды по названию

Популярные бренды