Comtrol RocketLinx ES7528 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 144

background image

Hardware Installation

RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

- 9

Hardware Installation

You can use the following subsections to install the RocketLinx ES7528:
•

Connect the Power

•

Mount the RocketLinx ES7528

on Page 10

•

Connect 10/100BASE-TX Ports

on Page 11

•

Connect Gigabit Ports (Combo Ports 25-28)

on Page 12

•

Connect SFP Transceivers (Combo Ports 25-28)

on Page 12

•

Connect the Digital or Relay Output

on Page 12

•

Panel Layout

on Page 13

Connect the Power

You can use the following procedure to connect power to the RocketLinx ES7528. The RocketLinx ES7528 is equipped with

both AC and/or DC1/DC2 power inputs.
The RocketLinx ES7528 provides redundant or aggregated power inputs (AC and/or

DC1/2). DC1 and DC2 inputs support reverse polarity protection. The RocketLinx

ES7528 will signal an alarm for loss of power on either DC1 or DC2.
1. Connect the power cord to the AC power input connector.

Note:

To reach the maximum total power budget, power inputs must be
aggregated. Refer to the following table for detailed information.

2. Connect the DC power inputs.

Note:

Power should be disconnected from the power supply before connecting it
to the switch. Otherwise, your screwdriver blade can inadvertently short
your terminal connections to the grounded enclosure.

a. Insert positive and negative wires into V+ and V- contacts.
b. Tighten the wire-clamp screws to prevent the wires from coming loose.
This table provides power supply specifications for the RocketLinx ES7528.

Electrical Specifications

Value

Power Input Voltage

DC1/DC2

802.3af 48VD

C (46-57VDC)

802.3at 53VD

C (50-57VDC)

AC and DC1/DC2

aggregated

53VDC

8.2A maximum

DC1/DC2 aggregated DC1=DC2

†

PSU/AC power

100-250VAC

47~63Hz

4A

PoE Output Voltage

802.3af

44-57VDC

802.3at

50-57VDC

Maximum PoE

Power/Port

802.3af 15.4W
802.3at

32W

Wire: 12 to 22 AWG

DC Input: 53VDC

«
...
7
8
9
10
11
...
»

Содержание RocketLinx ES7528

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для RocketLinx ES7528

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренд: Attwood Страницы: 2

Draco major K474-U8/C8

Бренд: Ihse Страницы: 167

Бренд: steute Страницы: 10

Бренд: Edge-Core Страницы: 9

2X2 VGA SWITCHER

Бренд: Gefen Страницы: 12

Edison Cooper Power Series

Бренд: Eaton Страницы: 12

Бренд: DeLOCK Страницы: 8

Бренд: Eagle Страницы: 2

Бренд: Justin Страницы: 8

Cross-8/HPoE-10G

Бренд: Evidence Страницы: 321

Бренд: Shure Страницы: 3

Бренд: Gefen Страницы: 9

Бренд: QNAP Страницы: 48

ADDERView Secure AVS-4128

Бренд: ADDER Страницы: 2

ADDERView CCS-MV4228

Бренд: ADDER Страницы: 2

ADDERView CCS-MV4224

Бренд: ADDER Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды