Comtrol RocketLinx ES7528 Скачать руководство пользователя страница 53

Страница: 53 / 144

Aggregation Status

RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

- 53

Aggregation Status

This page shows the status of port aggregation. Once the aggregation ports are negotiated, you will see the following status.

Aggregation Status

Description

Group ID

Displays Trunk 1 to Trunk 8 set up.

Type

Static or LACP set up.

Aggregated Ports

When LACP links, you can see the member ports in the Aggregated column.

Individual Ports

When LACP is enabled, member ports of LACP group that are not connected to

the correct LACP member ports are displayed in the Individual column.

Link Down Ports

When LACP is enabled, member ports of LACP group that are not linked up are

displayed in the Link Down column.

Load Balance

There are several load balance types based on dst-ip (Destination IP), dst-mac

(Destination MAC), src-dst-ip (Source and Destination IP), src-dst-mac (Source

and Destination MAC), src-ip (Source IP), src-mac (Source MAC).

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want to maintain these

settings if the RocketLinx ES7528 is powered off.

Содержание RocketLinx ES7528

















































































































































Результаты поиска

Содержание RocketLinx ES7528

Отзывы:

Похожие инструкции для RocketLinx ES7528

Бренды по названию

Популярные бренды

Comtrol RocketLinx ES7528, Руководство пользователя

Результаты поиска

Содержание RocketLinx ES7528

Отзывы:

Похожие инструкции для RocketLinx ES7528

Бренды по названию

Популярные бренды