Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 96

background image

Appendix B. Specifications and Notices

65

Technical Specifications

Technical
Specifications

This subsection lists the DeviceMaster ATS-XPE technical specifications.

•

Compact flash (512 MB) with pre-configured Windows XP operating system.
See

Default Operating System Configuration

on Page 66 for detailed

information.

•

NS GXLV/GX1-300 MMX 32-Bit x86 Processor that supports the Intel

®

MMX

instruction set extension for the acceleration of multi media applications. It
has 16 KB unified L1 cache, five-stage pipe lined integer unit, and an
integrated Floating Point Unit (FPU).

•

128 MB SDRAM system memory

•

AWARD 256 Kb flash memory BIOS

•

Display controller that has a MediaGx processor with 4 MB memory that
supports non-interlaced CRT monitors resolutions up to 1280 x 1024 @ 256
colors or 1024 x 768 @ 16 bpp.

•

10/100M bps Ethernet Controller, with two Realtek

™

RTL8139 IEEE802.u

100 BASE-TX standard dual auto-sensing interface to 10 Mbps or 100 Mbps
networks. On board RJ45 connectors provide for easy connection.

•

Serial ports on the motherboard.

-

AUX A

(COM2)

-

CONSOLE

(COM1)

•

Parallel port (DB25), which supports SPP/EPP/ECP mode.

•

PS/2 mouse connector (6-pin mini DIN) connector.

•

PS/2 keyboard connector (6-pin mini DIN) connector.

•

USB connector, which supports up to two USB devices.

•

Optional PC104 serial ports with a quadcable or octacable interface that is
software configurable with speeds up to 230.4 Kbps.

•

Optional PCMCIA slot for Comtrol approved devices that are pre-configured in
the ATS-XPE system.

Note:

The ATS-XPE PCMCIA option supports two Type II PCMCIA slots or
one Type III slot, which is installed at the factory. Drivers for Comtrol
approved PCMCIA devices are installed in the system.

-

Linksys EtherFast 10/100 + 56K Modem PC Card (PCMLM56)

-

Linksys Wireless PC card (WPC11)

The hardware supports Power management, but it is not supported by the
Windows XP Embedded operating system.

«
...
63
64
65
66
67
...
»

Содержание DeviceMaster ATS-XPE

































































































Отзывы:

Нет отзывов

Похожие инструкции для DeviceMaster ATS-XPE

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 2

Power Xpert Meter 2000

Бренд: Eaton Страницы: 16

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 84

Бренд: Aleratec Страницы: 12

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Juniper Страницы: 190

X-Pedition 2000

Бренд: Enterasys Страницы: 86

Бренд: Buffalo Страницы: 2

Бренд: insys icom Страницы: 4

Бренд: Moxa Technologies Страницы: 2

Бренд: HELVAR Страницы: 2

Бренд: HighPoint Страницы: 10

Бренд: CNC4PC Страницы: 11

Бренд: DigiTech Страницы: 6

PSoC 4 S Series

Бренд: Cypress Страницы: 4

Бренд: AMX Страницы: 1

Бренд: Alula Страницы: 4

B-Control Fader BCF2000

Бренд: Behringer Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды