Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 63

Страница: 63 / 96

Appendix B. Specifications and Notices

This section discusses the following topics:

•

Product specifications

Electromagnetic compliances

Environmental condition specifications

Hardware specifications

Technical specifications

Default operating system configuration

•

FCC Part 15 Class A notices

Product Specifications

The following subsections provide a variety of information about the DeviceMaster
ATS-XPE.

Electromagnetic
Compliances

The following table illustrates the status of electromagnetic compliance for the
ATS-XPE.

Electromagnetic Compliances

Status

Emission

Canadian EMC requirements

CISPR-22/EN55022

Class A

FCC Part 15 Class A

Yes
Yes
Yes

Immunity (motherboard):

EN55024: 1998

EN61000-4-2: 1995 ESD
EN61000-4-3: 1996 RF
EN61000-4-4: 1994 Fast Transient
EN61000-4-5: 1995 Surge
EN61000-4-6: 1996 Conducted disturbance
EN61000-4-8: 1993 Magnetic field
EN61000-4-11: 1994 Dips and Voltage Variations

Yes
Yes
Yes
Yes
Yes
Yes
Yes

Safety (power supply)

EN60950
UL / C-UL Listed

Yes
Yes

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды