Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 85

Страница: 85 / 96

Appendix D. Changing BIOS Configuration

Chipset Features Setup

The

Chipset Features Setup

screen primarily controls the board's chipset and is

used to change the chipset configuration.

This figure illustrates the DeviceMaster ATS-XPE factory defaults.

Note:

Improperly changing these default settings can result in an unstable system.

Power Management Setup

The

Power Management Setup

screen helps you handle the ROCKY-568SEV board’s

green

function. This feature can shut down the video display and hard disk to save

energy.

This figure illustrates the DeviceMaster ATS-XPE factory defaults.

USB Legacy Support : Disabled

Enabled

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды