Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 10

Страница: 10 / 96

Installation and Setup

Configuring the Network Settings on the ATS-XPE

Highlight

Internet Protocol (TCP/IP)

and select

Properties

Configure the network
connection to your network as
needed, and select

The default network settings for
the adapters are:

Adapter#1

IP Address
192.168.250.251
Subnet mask

255.255.255.0

Gateway

192.168.250.1

Adapter#2

IP Address
192.168.255.252
Subnet mask

255.255.255.0

Gateway

192.168.255.1

Note:

The PCMCIA adapter is
set to obtain an IP
address and has no
default address unless it
is manually configured.

Select

to save the Local Area

Connection Properties sheet and

Close

the Network Connections control panel.

The network connection will be available momentarily.

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды