Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 49

Страница: 49 / 96

Installing Serial Devices

Overview

The COM ports provided by the

SERIAL PORTS 1-8

can support any asynchronous

serial modem for use by any application that uses TAPI.

There is a remote possibility that connecting a peripheral using the wrong
configuration (

RS-232 device connected to a RS-422 configured port

) could

damage the peripheral. Configure each serial port specifically for the peripheral
that will be connected prior to connecting the peripheral to the ATS-XPE. See

Configuring the RocketPort Serial Ports

on Page 26 for information about

configuring port characteristics.

Note:

If your serial devices require a driver that does not support the Windows XP
Embedded system, contact Comtrol before driver installation.

Connect your serial devices to the configured ports using the appropriate cables. If
you need to build cables for RocketPort serial ports, see

RocketPort Serial Port

Connectors

on Page 30.

Installing Modems

This subsection illustrates how to install modems on ATS-XPE serial ports.

Make sure that you have the driver available to the ATS-XPE system.

If you have not done so, connect a modem to the

AUX A

CONSOLE

, or one of

the RocketPort serial ports.

Note:

The ATS-XPE will automatically detect the modem and start the Found
New Hardware Wizard.

Select

Install from a list or specific location (Advanced)

and

Next

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды