Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 30

Страница: 30 / 96

PC104 RocketPort Option

RocketPort Serial Port Connectors

The following subsections illustrate the pinouts for the quad- and octacable
connector types and how to build loopback plugs for testing serial ports.

DB9 Connectors

This illustrates
the pinouts for
DB9 quad- or
octacables.

Building Additional
DB9 Loopback Plugs

Loopback connectors

are DB9 female serial port plugs that you can use to test

serial ports. The ATS-XPE is shipped with a a single loopback plug (RS-232/422)
that corresponds to your quad- or octacable type.

Note:

You can run loopback tests with Test Terminal.

Wire the following pins together to build additional plugs or replace a missing RS-
232 loopback plug:

•

Pins 1 to 4 to 6

•

Pins 2 to 3

•

Pins 7 to 8 to 9

Wire the following pins together for an RS-422 loopback plug:

•

Pins 2 to 3

•

Pins 7 to 8

DB25 Connectors

This illustrates the pinouts for DB25 quad - or octacables.

Pin 1

Pin 6

RS-232

RI
CTS
RTS
DSR

GND
DTR
TxD
RxD
CD

Pin 1

Pin 6

RS-422

Not used
RxD+
TxD+
Not used

Not used*
Not used
TxD-
RxD-
Not used

Pin 1

Pin 6

RS-485

Not used
Not used
TxD/RxD+
Not used

Not used*
Not used
TxD/RxD-
Not used
Not used

Pin 5 is tied to ground on the board,

but is not used in the cable.

Pin 1

Pin 5

Pin 6

Pin 9

RS-232 Only
(Back View)

The RS-232 loopback plug
also works for RS-422.

Pin 1

Pin 5

Pin 6

Pin 9

RS-422 Only
(Back View)

Pin 1

Pin 14

TxD

RxD

RTS

CTS

DSR

Signal Gnd

DCD

DTR

RS-232

Pin 1

Pin 14

Signal Gnd

RS-422

Pin 1

Pin 14

TxD/RxD-

TxD/RxD+-

Signal Gnd

RS-485

RxD+
RxD-

TxD+

TxD-

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды