Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 84

Страница: 84 / 96

Appendix D. Changing BIOS Configuration

Standard CMOS Setup

The

Standard CMOS Setup

screen is used for basic hardware system configuration,

such as the Date and Time settings.

This figure illustrates the DeviceMaster ATS-XPE factory defaults.

Use the following procedure to change the system date.

Press either the Arrow or <

Enter

> key on your keyboard to select one of the

fields (Month, Date or Year).

Press either <

PgUp

> or <

PgDn

> to increase or decrease the value of that field.

Use the same key sequence to change the time setting.

BIOS Features Setup

The

BIOS Features Setup

screen is designed for fine-tuning your system and

improving its performance. Typically, you do not have to change the default
settings, which are pre-set for the most reliable operation.

This figure illustrates the DeviceMaster ATS-XPE factory defaults.

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды