Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 8

Страница: 8 / 96

Installation and Setup

Other Installation and Configuration Procedures

Other Installation
and Configuration
Procedures

After the initial installation of the hardware there are other procedures you may
need to perform to complete installation and configuration of the ATS-XPE.

•

If you want to connect and configure the ATS-XPE to a network (Ethernet or
PCMCIA wireless adapter), review and perform the appropriate procedures:

PCMCIA wireless option

, see

Linksys Wireless PC Card (WPC11)

on Page

43 to complete the wireless card installation.

Configuring the Network Settings on the ATS-XPE

on Page 9, for initial

setup of the Ethernet ports or the Linksys PCMLM56 Ethernet card.

Changing the Default Computer and Workgroup Names

on Page 11, if you

are configuring multiple ATS-XPE units on your network.

•

If you installed a PCMCIA modem, perform the appropriate procedures:

Starting Routing and Remote Access Services

starting on Page 13, to start

remote services.

Setting Up Dial-In

on Page 15, if you want to configure the PCMCIA

modem for dial-up on the ATS-XPE.

•

If you ordered the PC104 RocketPort option, see

Configuring the RocketPort

Serial Ports

on Page 26 before connecting your serial devices.

Note:

Only install serial device drivers for the Windows XP Embedded
operating system. Refer to the

Customer Support Policy

on Page 56,

before installing any drivers.

•

See

Installing Modems

starting on Page 49, if you want to connect an external

modem to the

AUX A

CONSOLE

ports.

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды