Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 96

background image

Certified PCMCIA Adapters

43

Certified PCMCIA Adapters

This section discusses configuration issues for Comtrol certified PCMCIA options.

Comtrol Certified PCMCIA Devices

The ATS-XPE supports the following PCMCIA devices.

•

Any standard PCMCIA to Compact Flash adapter

•

Linksys Wireless PC Card (WPC11)

•

Linksys EtherFast 10/100 + 56K Modem PC Card (PCMLM56)

Note:

The ATS-XPE PCMCIA option supports two Type II PCMCIA slots or one
Type III slot, which is installed at the factory. Drivers for Comtrol approved
PCMCIA devices are installed in the system.

Linksys Wireless PC Card (WPC11)

The device driver for the Linksys Wireless PC Card (WPC11) is installed on the
ATS-XPE. To configure the Linksys Ethernet card, it is necessary to have a
configured and operating wireless access point connected to the local network and
have it situated within range of the wireless adapter (preferably less than 100 feet
indoors with no obstructions).

For support of the card, see

http://www.linksys.com

.

1.

Select

Install from a specific list or specific location (Advanced)

and

Next

.

«
...
41
42
43
44
45
...
»

Содержание DeviceMaster ATS-XPE

































































































Отзывы:

Нет отзывов

Похожие инструкции для DeviceMaster ATS-XPE

Бренд: BandLuxe Страницы: 67

Бренд: VAF instruments Страницы: 56

DR-4100P Series

Бренд: Idis Страницы: 30

Бренд: Alacritech Страницы: 20

Sure Cross DX70

Бренд: Banner Страницы: 35

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Бренд: Garderos Страницы: 23

Бренд: HighPoint Страницы: 10

Бренд: ADIC Страницы: 140

Бренд: Hama Страницы: 25

Бренд: Infoblox Страницы: 16

Бренд: ADDON Страницы: 4

Air Live GW-300R

Бренд: Ovislink Страницы: 20

EZ Switch SMC-EZ1024FDT

Бренд: SMC Networks Страницы: 4

Бренд: KYLAND Technology Страницы: 19

Бренд: TRENDnet Страницы: 10

Бренд: ActionTec MI424WR Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды