Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 47

Страница: 47 / 96

Certified PCMCIA Adapters

Linksys EtherFast 10/100 + 56K Modem PC Card (PCMLM56)

11. To configure the card exclusively for a specific network, select

View Available

Wireless Networks

12. Highlight the appropriate network connection and

Advanced

13. Select

Access point (infrastructure) networks only

and

Close

14. Select

to close the Wireless Network Connection Properties window and

close the Network Connections control panel.

15. Go to

Configuring the Network Settings on the ATS-XPE

on Page 9 to configure

the card for your network.

Linksys EtherFast 10/100 + 56K Modem PC Card (PCMLM56)

Although the Linksys PCMLM56 driver for this adapter is pre-configured into the
ATS-XPE as COM3, you must start remote access service and you may need to
select a country code if you are using it outside North America.

See

Starting Routing and Remote Access Services

on Page 13 and

Setting Up Dial-

on Page 15, if necessary to complete the configuration.

For support of the card, see

http://www.linksys.com

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды