Comtech EF Data SDM-2020 Скачать руководство пользователя | Manualshive

Страница: 71 / 215

background image

SDM-2020 Satellite Demodulator

Operation

Rev. 3

3–27

3.3.3.4

Common Equipment Faults Menu

Refer to Figure 3-9.

Fault/Alarm

Possible Problem and Action

BATTERY/CLOCK

M&C battery voltage or clock fault. Indicates a low voltage in the memory
battery.

Note:

Typically will be active when a demodulator has been Hard Reset, or

the firmware has been changed, and the demodulator is first turned On. If the
fault occurs without a firmware change or hard reset of the demodulator,
replace the battery on the demodulator board (PL/5746).

-12 VOLT SUPPLY

-12V power supply fault. Indicates a high or low voltage condition. Level is

±

5%.

Check the -12V line from the power supply or on the board. Check TP17 on
the demodulator board (PL/5746), to verify the proper -12V monitor voltage.
If this voltage is not at the proper level, this would indicate the power supply
is faulted. Return demodulator for repair.

+12 VOLT SUPPLY

+12V power supply fault.

Use the same procedure as with -12V Supply fault. To verify the +12V power
supply voltage, check TP19 on the demodulator board (PL/5746). A voltage
of 12V (± 5%), will be monitored when the +12V is at the proper level.

+5 VOLT SUPPLY

+5V power supply fault.

Use the same procedure as with -12V fault. To verify the +5V power supply
voltage, check TP5 on the demodulator board (PL/5746). A voltage of 5V (±
5%), will be monitored when the +5V is at the proper level.

CONTROLLER

Controller fault. Indicates loss of power in the M&C card.

Note:

Typically indicates the controller has gone through a power On-Off

cycle.

LNB

LNB fault. Indicates loss of LNB during operation

Note:

Typically indicates the LNB has gone through a power On-Off cycle.

«
...
69
70
71
72
73
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: Polytron Страницы: 32

Бренд: Alcad Страницы: 5

Бренд: Alcad Страницы: 12

Бренд: Alcad Страницы: 12

Бренд: Casio Страницы: 12

Бренд: Casio Страницы: 19

Бренд: Casio Страницы: 57

Бренд: Casio Страницы: 44

Бренд: Casio Страницы: 80

Бренд: Casio Страницы: 91

FX-61F SCIENTIFIC CALCULATOR

Бренд: Casio Страницы: 45

Бренд: Casio Страницы: 17

Бренд: Citizen Страницы: 20

Бренд: Televes Страницы: 20

watch any where Double

Бренд: JollyLine Страницы: 12

Бренд: MiLAN Страницы: 64

Бренд: MiLAN Страницы: 84

Бренд: MiLAN Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды