Comtech EF Data SDM-2020 Скачать руководство пользователя | Manualshive

Страница: 139 / 215

background image

Data Interfaces

SDM-2020 Satellite Demodulator

A–38

Rev.3

A.5.5

Monitor and Control Functions

A.5.5.1 System

Implementation

Refer to Table A-21 for signal definition.

Table A-21. Signal Definition

Signal

Definition

TA (Data Terminal Equipment Available)
LA (Loopback Circuit A)
LB (Loopback Circuit A)

These signals are inputs from the HSSI interface. The state of these inputs is
read by the M&C from the ECL/HSSI interface status register.

CA (Data Communication Equipment Available)
LC (Loopback Circuit C)
TM (Test Mode)

These signals are outputs from the HSSI interface. The state of these outputs
is controlled by the M&C writing the ECL/HSSI interface control register.

TA

This signal indicates the DTE is available for data transfers. When the DTE
is not available the RF output will be turned Off and the DTE status menu
shall reflect DTE unavailable.

LA and LB loopback input control signals

These signals are available to the M&C, but no functional support is
required.

Upon Modem power-up the CA output is set UNAVAILABLE until all modem
initialization has been completed and no faults are detected. After completion of
initialization the CA line is set AVAILABLE. Any detectable faults that cause the
modem to be place in an non-operational mode shall set CA UNAVAILABLE.

TM output shall be set ACTIVE if the ECL/HSSI interface is commanded into Loopback
mode. TM shall be INACTIVE for all other modes.

LC output is not supported, and is set inactive for all modes.

A.5.5.2 Faults

Refer to Table A-22 for ECL/HSSI fault indicators to the HSSI connector (Reserved
DCE pins) from the modem interface.

Table A-22. Fault Signal Definitions

Signal

Definition

Carrier Detect (CD)

Indicates Demodulator carrier tracking loop locked. Status output. TTL output. Active
High (programmable).

Modulator Fault (DF)

Open collector TTL signal indicating Demodulator fault. Active High. An external
pull-up resistor is required.

Modulator Fault (MF)

Open collector TTL signal indicating Modulator fault. Active High. An external pull-
up resistor is required.

«
...
137
138
139
140
141
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: B meters Страницы: 14

EKSELANS MD HD EASY

Бренд: ITS Telecom Страницы: 8

Бренд: Casio Страницы: 31

SMART PICKER SERIES

Бренд: LaCoSys Страницы: 20

ULTRA MEASURE MASTER 8025

Бренд: Calculated Industries Страницы: 47

Бренд: Salient Страницы: 10

Бренд: GSS Страницы: 41

Бренд: GSS Страницы: 46

Бренд: Velleman Страницы: 4

Бренд: Samsung Страницы: 129

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Ataba Страницы: 2

Бренд: CE Labs Страницы: 1

Бренд: Sencor Страницы: 14

Бренд: Kenwood Страницы: 6

Бренд: Kenwood Страницы: 9

DIVITRON QAM 4x4 FTA

Бренд: tron Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды