Comtech EF Data SDM-2020 Скачать руководство пользователя страница 66

Страница: 66 / 215

Operation

SDM-2020 Satellite Demodulator

3–22

Rev. 3

3.3.3 Faults/Alarms

Menus

Refer to Figure 3-9.

The Faults/Alarms level is accessible from the Function Select menu. These are similar
to monitor functions, as the current status is displayed.

Press [

←

] or [

→

] to move between the Fault/Alarm groups:

•

Demodulator faults

•

Receive Interface faults

•

Common Equipment faults

The current Faults/Alarms status is displayed on line 2 of the display in real time.

Fault status is displayed as a “+” (plus) or “-” (minus) for each parameter monitored:

•

“-” indicates that no fault or alarm exists.

•

“+” indicates that a fault exists, and will cause switching in a redundant system.

•

A reversed-contrast “+” sign appearing on the display indicates an alarm is
active.

Note:

Alarms do not cause switching to occur.

To display labels for individual faults or alarms, press [ENTER]. Press [

←

] or [

→

] to

move the flashing cursor to the fault or alarm to be identified. The label for that
fault/alarm is immediately displayed on line 1 of the display.

To exit this level of operation and return to the previous level, press [CLEAR].

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды