Comtech EF Data SDM-2020 Скачать руководство пользователя страница 90

Страница: 90 / 215

Operation

SDM-2020 Satellite Demodulator

3–46

Rev. 3

3.3.5.3

Utility System Menu

Refer to Figure 3-13.

TIME/DATE

Time of day and date set/display function.

The current time and date in the demodulator memory are displayed when
selected. To set the demodulator time and/or date, press [ENTER]. Press [

←

]

or [

→

] to position the flashing cursor over the parameter to be changed. Press

[

↑

] or [

↓

] to change the parameter to the desired value. Once the parameters

are displayed as desired, press [ENTER]

to set the time and date.

REMOTE BAUD
RATE/PARITY

The current baud rate and parity selection of the demodulator are displayed.

To set the demodulator baud rate and/or parity, press [ENTER]. Press [

←

] or

[

→

] to position the flashing cursor over the parameter to be changed. Press

[

↑

] or [

↓

] to change the parameter to the desired value. Once the parameters

are displayed as desired, press [ENTER]

to set the baud rate and parity. The

baud rate can be set at 300, 600, 1200, 2400, 4800, 9600, or 19200. The
parity can be set to EVEN, ODD, or NONE.

REMOTE ADDRESS

The current demodulator address is displayed (1 to 255).

To set the remote address, press [ENTER]. Press [

↑

] or [

↓

] to change the

parameter to the desired value. Press [ENTER]

to execute the change.

Note:

Address 0 is reserved as a global address.

REMOTE TYPE

Remote interface type selection, choices include:

•

RS-485 (4-wire)

•

RS-485 (2-wire)

•

RS-232

Press an arrow key to make the selection. Press [ENTER] to execute the
change.

YEAR DISPLAY

Displays the current year as a 2-digit or a 4-digit number:

Example:

(2-Digit) 99

(4-Digit) 2000

TEST MODE STATUS

Test mode status indicator. The following demodulator test points are listed in
this window and will display a “+” when a test mode is active:

•

DEMOD FAULTS

•

INTF FAULTS

•

2047 PATTERN

•

RS CORR OFF

•

INTRFCE LOOPBACK

To view the test modes, press [ENTER]. Press [

←

] or [

→

] to move through

the list of test modes.

LAMP TEST ??

Lamp test function to verify the front panel indicators.

Press [ENTER]

to turn on all of the front panel indicators for 3 seconds.

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды