Comtech EF Data SDM-2020 Скачать руководство пользователя

Страница: 160 / 215

SDM-2020 Satellite Demodulator

Data Interfaces

Rev.3

A–59

A.7.3 Interface

Specifications

The following sections describe the detailed requirements for the SMPTE-310M data
interface.

A.7.3.1 Specification

Summary

Refer to Table A-34 for SMPTE-310M specifications.

Table A-34. SMPTE-310M Specification Summary

Video Interface (Terrestrial)

Signal Type

Biphase mark coded synchronous serial data per SMPTE-310M and TM

1449.

Connector Type

Ω

BNC.

Interface and Connector
Impedance

Resistive 75

Ω

unbalanced, per SMPTE-310M.

TX and RX Signal Level

800 mV

10% per SPMTE-310M.

DC Offset

0.0 V

0.5 V.

Rise And Fall Times

The rise and fall times, determined between the 20 and 80% amplitude

points shall be within 0.4 ns and 5.0 ns and shall not differ by more than
1.6 ns, per SMPTE-310M.

Overshoot

10% maximum (on both rising and falling edges) per SPMTE-310M.

Receiver Sensitivity

The receiver shall operate with up to 3 dB amplitude loss at 1/2 the

interface clock.

Return Loss

30 dB minimum, 100 kHz to the interface clock frequency per

SMPTE-310M.

ATSC Data Rate

8VSB: 19.392 658 46 Mbit/s = (4.5 E6) x (684/286) x (564/313)

Clock Accuracy

Programmed data rate

100 ppm.

Clock Jitter, Drift And
Wander

The interface clock frequency error (drift limit) shall not exceed

2.8 ppm.

The rate of frequency change (drift rate) shall not exceed 0.028 ppm/s.
The jitter in the timing of the interface signal transitions shall not exceed

2 ns p-p, measured over a bandwidth of 1 Hz to 1/100 of the interface
clock frequency.

Cable Length, Typical

RG59

180 meters (591 feet)

Belden 8281

250 meters (820 feet)

Auxiliary Function Port

Signals

DF (Demodulator Fault, open-collector output).
CD (Demodulator Carrier Detect, TTL output).
RTS (Modulator Control, TTL input)

Connector

9 Pin D, female.

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды