Comtech EF Data SDM-2020 Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 215

background image

Fast Option

SDM-2020 Satellite Demodulator

C–2

Rev. 3

Notes:

1. Units that shipped on are after October 12, 1998 are DVB compliant for 8PSK.
2. Units that shipped prior to October 12, 1998 can be upgraded for 8PSK-DVB

compliance.

3.

Contact ADAP Customer Support department for additional information.

4.

Software version – see main menu of LCD.

5.

Refer to Ultility System menu for:
a.

M&C firmware,

b. Boot firmware,
c.

FPGA firmware.

6. The 2- and 4-input L-Band require the correct hardware. Check Utility

Demodulator Options menu for status.

C.1.1

FAST System Theory

FAST is an enhancement feature available only in ADAP products, enabling on-location
upgrade of the operating feature set—in the rack—without removing the unit from the
setup. When service requirements change, the operator can upgrade the topology of the
unit to meet those requirements within minutes after confirmation by ADAP. This
accelerated upgrade can be accomplished only because of FAST’s extensive use of
programmable devices incorporating ADAP-proprietary signal processing techniques.
These techniques allow the use of a unique access code to enable configuration of the
available hardware. The access code can be purchased from ADAP. Once obtained, the
access code is loaded into the unit through the front panel keyboard or the rear remote
port.

With the exclusive FAST technology, operators have maximum flexibility for enabling
functions as they are required. FAST allows an operator to order a modem precisely
tailored for the initial application, reducing risk and cost overruns during the application
integration process.

C.1.2 Implementation

FAST is factory-implemented in the unit at the time of order. Hardware options for basic
unit can be ordered and installed either at the factory or in the field. The operator can
select options that can be activated easily in the field, depending on the current hardware
configuration of the unit.

«
...
203
204
205
206
207
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: ibico Страницы: 18

Бренд: Pico Macom Страницы: 8

Бренд: Sennheiser Страницы: 2

Бренд: Toner Страницы: 15

Бренд: Satlink Страницы: 10

Calc-u-vue LER 0068/50

Бренд: Learning Resources Страницы: 4

Бренд: Citizen Страницы: 15

Бренд: Citizen Страницы: 11

Бренд: Citizen Страницы: 14

Бренд: Citizen Страницы: 16

Бренд: Citizen Страницы: 24

Бренд: Citizen Страницы: 28

Бренд: Citizen Страницы: 35

Бренд: Citizen Страницы: 40

Бренд: Citizen Страницы: 48

Бренд: Citizen Страницы: 45

Бренд: Citizen Страницы: 66

Бренд: Citizen Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды