Comtech EF Data SDM-2020 Скачать руководство пользователя

Страница: 39 / 215

SDM-2020 Satellite Demodulator

Installation

Rev. 3

2–7

Table 2-1. Rear Panel Connectors

Name

Ref. Desig.

Type

Function

Remote

9-pin D, Female

Remote control (M&C)

Fault

9-pin D, Female

Relay Faults

Monitor

J21

9 pin D, Female

Performance Monitor

IF Input (Single-Channel)

(see Note 1)

J23

Type F, Female

RX IF input, LNB power out.

IF Input (4 Input)

(see Note 2)

J23, J24,

J25, J26

Type F, Female

RX IF Input LNB power out

Prime Power

None

Standard

AC Power Input

GND

None

#10-32 Stud

Chassis Ground

Data Interface Connectors

See Appendix A

Notes:

Single RX IF input is for earlier L-Band units and all 70/140 MHz demodulators. LNB
power is available only for L-Band.

The 4-channel input IF is only available for L-Band.

2.3.1

Connector Pinout Definitions

Pinout “TYPE” is defined to described signal direction for each pin. The signal direction
is relative to the connector.

Definitions for Pinout Types

I (Input)

A signal goes into the connector.

O (Output)

A signal exits the connector.

I/O (Input/Output)

A signal both enters and exits the connector on the specified pin.

GND (Ground)

The pin is defined as being connected to a power supply ground or return.

N/A (Not Assigned)

The pin is not assigned within the system but may be routed to other connectors.
Usually defines spare pins.

N/C (No Connect)

The pin is not connected and is not used within the system.

N/U (Not Used)

The pin is not used but is routed and has other uses within the system.

FC (Form C)

The pin is connected to a “Form C” relay.

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды