Comtech EF Data SDM-2020 Скачать руководство пользователя

Страница: 111 / 215

Data Interfaces

SDM-2020 Satellite Demodulator

A–10

Rev.3

A.2.4.2.1

Connector Pinouts, J4, EIA-530

The connector is a sub-miniature, 25-pin, female D connector, with threaded jack nuts
(refer to Table A-5 for pinout).

Signal functions are as defined in EIA-530.

Notes:

The differential sense of all signals is a logic “1” when “B” is positive with
respect to “A,” as defined in EIA-530.

Only those pins indicated as “Demodulator” in the table are applicable.

Table A-5. EIA-530 Serial Interface Connector Pinout (J4)

Pin #

Signal Function

Name

Type

Comment

530 Shield

Shield

Mod/Demod

Transmit Data (TD-A)

BA-A

Modulator

Receive Data (RD-A)

BB-A

Demodulator

Request To Send (RS-A)

CA-A

Modulator

Clear To Send (CS-A)

CB-A

Modulator

DCE Ready (DM-A)

CC-A

Demodulator

Signal Ground

GND

Receive Line Signal Detect (RR-A)

CF-A

Demodulator

Receive Timing (RT-B)

DD-B

Demodulator

Receive Line Signal Detect (RR-B)

CF-B

Demodulator

Terminal Timing (TT-B)

DA-B

Modulator

Send Timing (ST-B)

DB-B

Modulator

Clear To Send (CS-B)

CB-B

Modulator

Transmit Data (TD-B)

BA-B

Modulator

Send Timing (ST-A)

DB-A

Modulator

Receive Data (RD-B)

BB-B

Demodulator

Receive Timing (RT-A)

DD-A

Demodulator

N/C

Request To Send (RS-B)

CA-B

Modulator

N/A

Demodulator Fault (DF)

N/A

Demodulator

DCE Ready (DM-B)

CC-B

Demodulator

N/A

Terminal Timing (TT-A)

DA-A

Modulator

Modulator Fault (MF)

N/A

Modulator

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды