Comtech EF Data SDM-2020 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 215

background image

Data Interfaces

SDM-2020 Satellite Demodulator

A–60

Rev.3

Table A-34. SMPTE-310M Specification Summary (Continued)

Monitor and Control

Monitored Functions

TX – PLL Lock (monitors presence of input data)
TX – State of RTS input on auxiliary function port
TX - FPGA load failure.
RX - FIFO Underflow/overflow.
RX - PLL lock.

RX - FPGA load failure.

Controlled Functions

Interface Loopback.
Interface Loop-through

General

Framing Formats
(to be provided by the
demodulator, not this
interface)

187 (no framing, pass-through mode).

188 (DVB/MPEG2 frame consisting of a sync. byte and 187 data bytes).

204 (frame consisting of sync. byte , 187 data bytes and 16 Reed-Solomon

check bytes).

Environmental

Operating Temperature
Storage Temperature
Humidity

0 to + 50

°

C (32 to + 122

°

F)

-40 to + 70

°

C (-40 to +158

°

F)

Up to 95% non-condensing.

Physical

Size

SDM-2020 plug-in module compatible.

Hot Pluggable

Not required. Unit power is turned off prior to removal or insertion of the data
interface.

A.7.3.2

Interface Loopback Mode

Refer to Figure A-18.

In loopback mode, data entering the TX connector is returned to the RX output connector
after passing through the interface. The data entering the interface at the TX input is
routed all the way through the TX path and out to the modulator at J1. All TX signals
going to the modulator are routed back to the RX path in place of the normal signals,
which would be coming from the demodulator.

•

In a Modulator, TX data continues to enter the modulator and is TX during loopback.

•

In a Demodulator, satellite data is not routed through the SMPTE-310M Data Interface.

A.7.3.3

Interface Loop-Through Mode

In loop-through mode (Modulator Only), operation is the same as in loopback mode,
however, the test mode LED indications are not activated.

«
...
159
160
161
162
163
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: Sharp Страницы: 2

Бренд: ibico Страницы: 18

Бренд: QM Страницы: 2

B-QAM-HDMI-IP-4CH

Бренд: Questtel Страницы: 36

Бренд: Brother Страницы: 11

MultiView TI-30XS

Бренд: APH Страницы: 2

Бренд: MultiScreen Страницы: 4

Бренд: Satson Страницы: 17

Бренд: Rebel Страницы: 23

MicroModulator MM70

Бренд: NetMedia Страницы: 1

TriplePlay NM-MM73S

Бренд: NetMedia Страницы: 4

Бренд: NetMedia Страницы: 4

TriplePlay MM73

Бренд: NetMedia Страницы: 4

Бренд: Maximum Страницы: 10

Бренд: UNITED OFFICE Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды