Comtech EF Data SDM-2020 Скачать руководство пользователя | Manualshive

Страница: 194 / 215

background image

SDM-2020 Satellite Demodulator

Remote Control Operation

Rev. 3

B–19

Bit 6 = 1 always.
Bit 5 through Bit 0 reserved.

Character 'g': Common equipment fault status character 1.

Bit 6 = 1 always.
Bit 5 = reserved.
Bit 4 through Bit 0 = Binary representation.
(0 to 10) of the number of common equipment stored
faults.

Character 'h': Common equipment fault status character 2.

Bit 6 = 1 always.
Bit 5 = Battery/Clock.
Bit 4 = -12 volt power supply.
Bit 3 = +12 volt power supply.
Bit 2 = +5 volt power supply.
Bit 1 = LNB.
Bit 0 = Monitor & Control Module.

Change
Status

Command:
Response:

<add/CS_'cr'
>add/CS_x'cr''lf']

Where: The 'x' character is defined as follows:

'@' = no change since last BCS_ and BCSF_ polls.

'A' = BCS_ response has changed since last BCS_ poll.

'B' = BCSF_ response has changed since last BCSF_ poll.

'C' = Both responses have changed since last BCS_ and
BCSF_ polls.

This command indicates that a change has or has not
occurred on either the BCS_ or the BCSF_ response since the
last BCS_ or BCSF_ poll.

Equipment
Type

Command:
Response:

<add/ET_'cr'
>add/ET_tttttttt_xxx.yyy.zzz'cr''lf']

Where:

tttttttt = Equipment type.
xxx.yyy.zzz = Software version.

This command returns the equipment type and the software
version of the addressed device.

Monitor &
Control
Firmware
Information

Command:
Response:

<add/MCFI_'cr'
>add/MCFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yyyy'cr''lf']

Where:

xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999).

nnnnnn = Firmware number (0 to 999999).

dd = Firmware dash number (0 to 99).

r = Firmware revision (-, or A to Z).

Boot
Control
Firmware
Information

Command:
Response:

<add/BFI_'cr'
>add/BFI_'cr'
VER_xxx.yyy.zzz’cr’
FW/nnnnnn-ddr'cr'
mm/dd/yyyy'cr''lf']

Where:

nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999)

Note: If Dash number is not used, '-dd' will be reported.

DATA ROM
Firmware
Information

Command:
Response:

<add/DFI_'cr'
>add/DFI_'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yyyy'cr''lf']

Where:

nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).

Note: If Dash number is not used, '-dd' will be reported.

«
...
192
193
194
195
196
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: Thor Broadcast Страницы: 17

Бренд: Novus Страницы: 22

Бренд: Lemco Страницы: 22

Бренд: York Страницы: 283

Бренд: Q-Connect Страницы: 37

Бренд: Q-Connect Страницы: 36

Бренд: Q-Connect Страницы: 40

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 64

Бренд: Sharp Страницы: 2

Бренд: techem Страницы: 144

Бренд: SwissMicros Страницы: 4

Бренд: Aiphone Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды