Comtech EF Data SDM-2020 Скачать руководство пользователя

Страница: 199 / 215

Remote Control Operation

SDM-2020 Satellite Demodulator

B–24

Rev. 3

Interface
Buffer Fill
Status

Command:
Response:

<add/IBFS_’cr’
>add/IBFS_nn%’cr’’If’]

Where: nn = 1 to 99 (Relative to buffer depth.)

Where ‘pn’ is the last parameter returned.

Parameter

Number

Parameter Name

(Command Reference

Description

29 to 32

RX Interface Coding Format

(ref. ICFR_ command)

Interface Loopback

(ref. ILB_ command)

Buffer Clock Source

(ref. BC_ command)

Interface Buffer Size

(ref. IBS_ command)

External Reference Frequency

(ref. ERF_ command)

TX Terrestrial Clock Frequency

(ref. TRF_ command)

Reserved

p23 = n, where n = 0 (AMI), 1 (B3ZS), 2 (HDB3), 3 (B8ZS).

p24 = n, where x = 0 (Off) or 1 (On).

p25 = n, where x = 0 (Off) or 1 (On).

p26 = nnnnnn, buffer size in milliseconds

p27 = nnnnn.n external frequency in kHz

p28 = nnnnn, external reference frequency in Mbit/s

B.9.5

SMPTE 310M Interface Commands

Interface
Loopback

Command:
Response:

Status:
Response:

<add/ILB_xxx'cr'
>add/ILB_xxx'cr''lf']

<add/ILB_'cr'
>add/ILB_xxx'cr''lf']

Where: xxx = ON or OFF

Interface
Firmware
Information

Command:
Response:

<add/IFI_'cr'
>add/IFI_'cr''lf']

FW/nnnnn-dr’cr’
mm/dd/yyyy’cr’’If’]

Where: nnn = Firmware number (0 to 999999).

d = Firmware dash number (0 to 99)
r = Firmware revision (-, or A to Z)

Where ‘pn’ is the last parameter returned.

Parameter

Number

Parameter Name

(Command Reference

Description

24 thru 32

Interface Loopback

(ref. ‘ILB_”command).

Reserved

p23 = n, where x = ‘0’ (OFF), ‘1’ (ON)

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды