Comtech EF Data SDM-2020 Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 215

background image

Data Interfaces

SDM-2020 Satellite Demodulator

A–52

Rev.3

A.6.6

Interface Loop - Through

The interface provides a “Loop-Through” mode of operation. The loop-through mode is
intended to allow synchronization of RX data (RD) to send data (SD) when an
SDM-2020 demodulator and a SDM-2020 modulator are co-located (see Figure A-17)
Loop-through mode is selectable only when the G.703 interface is installed in an SDM-
2020 modulator.

•

Interface Operation Within SDM-2020 Modulator

When loop-through mode is executed (turned on) send data (SD) at the input to
the interface is routed to both the interface receive data (RD) output and the host
modulator data input. This mode of operation does not

interfere with

transmission of data over the satellite link. Transparent to the user, the following
actions occur on the interface:

♦

Recovered clock and data from the send data (SD) input is looped to the
interface RX data path.

♦

Interface RX data rate and line coding are set the same as TX.

♦

The RX Doppler/plesiochronous buffer is set for minimum depth and buffer
reference clock is set to TX Terrestrial.

•

Interface Operation Within SDM-2020 Demodulator

Although loop-through mode is not selectable when the G.703 interface is
installed in a SDM-2020 demodulator,

the following items must be considered

when setting up the demodulator.

♦

Connect receive data (RD) output of the co-located modulator to the send
data (SD) of the co-located demodulator.

♦

Set the interface transmit data rate and line coding the same as the co-located
modulator.

♦

Set the G.703 interface buffer clock reference to Transmit Terrestrial.

«
...
151
152
153
154
155
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: Texas Instruments Страницы: 507

Бренд: Yamaha Страницы: 4

ESLI MATE EL-2128V

Бренд: Sharp Страницы: 2

Elsimate EL-S25

Бренд: Sharp Страницы: 2

ELSIMATE EL-M332

Бренд: Sharp Страницы: 2

ELSIMATE EL-782C

Бренд: Sharp Страницы: 2

ELSIMATE EL-344R

Бренд: Sharp Страницы: 2

Бренд: Quer Страницы: 24

Construction Master III

Бренд: Calculated Industries Страницы: 55

Бренд: FeinTech Страницы: 8

Бренд: UNITED OFFICE Страницы: 28

4065 Construction Master Pro v3.0

Бренд: Calculated Industries Страницы: 110

TI-84 Plus CE Python

Бренд: Texas Instruments Страницы: 6

Бренд: DekTec Страницы: 50

M32 M32QR ANTILOCK MODULATOR ASSY

Бренд: BENDIX Страницы: 8

M-30 ANTILOCK MODULATOR ASSY

Бренд: BENDIX Страницы: 8

Бренд: BENDIX Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды