Comtech EF Data SDM-2020 Скачать руководство пользователя страница 94

Страница: 94 / 215

Operation

SDM-2020 Satellite Demodulator

3–50

Rev. 3

3.3.5.4

Utility Demodulator Options Menu

Refer to Figure 3-14.

REV EMULATION

Programs an emulation mode of a previous functional revision.

Revision emulation allows the user interfaces (either front panel or remote) to
emulate a previous version of software.

Upon entry, the CURRENT VERSION is displayed. Press a directional key to
select the FUNCTIONAL versions. Press [ENTER] to execute the change.

Note:

The Utility menu numbers increase with each software version change.

DEMOD OPTIONS

(Status Only)

Displays the following demodulator options:

•

OEM LCD

•

8PSK

•

16QAM

•

2 L-Band Inputs

•

4 L-Band Inputs

•

70/140 MHz

If the option is installed, the “+“ (plus) symbol is displayed to the right of
the option

If the option is not installed, but is a FAST upgrade the “-“ (minus)
symbol is displayed to the right of the option.

If the option is not installed and not upgradable, the “0” symbol is
displayed to the right of the option.

If the option is not installed, but is field upgradable, the “X’” symbol is
displayed to the right of the option.

MODEM
EMULATION

Displays DISABLED or EMULATION VERSION.

DEMOD SERIAL #

(Status Only)

Displays the demodulator serial number.

CONFIGURATION
CODE–DEMOD

EFData supplied code (FAST).

On entry, the current configuration code is displayed with the flashing cursor
on the first character. Press [

←

] or [

→

] to move the flashing cursor. Press [

↑

]

or [

↓

] to increment or decrement the digit at the flashing cursor. Press

[ENTER] to execute the change.

Entering this code enables the corresponding demodulator option. To purchase
an option, contact EFData Customer Support for more information.

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды